I'm doing postmortem on a 2048 node (16384 rank) job on Edison, and trying to understand why my I/O performance might have been slow. Here's the data: Measured I/O bandwidth: slice 35 write sparse bandwidth = 6082640 / (3.52519e+06 s / 16384) = 2.63287e-05 GB/s slice 34 write sparse bandwidth = 13824080 / (3.66608e+06 s / 16384) = 5.75379e-05 GB/s slice 33 write sparse bandwidth = 24754256 / (2.83647e+06 s / 16384) = 0.000133166 GB/s slice 32 write sparse bandwidth = 39370832 / (3.47016e+06 s / 16384) = 0.000173119 GB/s slice 31 write sparse bandwidth = 55812176 / (2.53623e+06 s / 16384) = 0.000335785 GB/s slice 30 write sparse bandwidth = 74741840 / (2.5714e+06 s / 16384) = 0.00044352 GB/s slice 29 write sparse bandwidth = 93560912 / (2.67336e+06 s / 16384) = 0.000534019 GB/s slice 28 write sparse bandwidth = 112803920 / (2.74639e+06 s / 16384) = 0.000626733 GB/s slice 27 write sparse bandwidth = 128194640 / (3.1603e+06 s / 16384) = 0.000618958 GB/s slice 26 write sparse bandwidth = 141281360 / (3.12754e+06 s / 16384) = 0.00068929 GB/s slice 25 write sparse bandwidth = 148193360 / (2.62376e+06 s / 16384) = 0.000861835 GB/s slice 24 write sparse bandwidth = 151861328 / (3.2145e+06 s / 16384) = 0.000720865 GB/s slice 23 write sparse bandwidth = 148193360 / (2.44736e+06 s / 16384) = 0.000923956 GB/s slice 22 write sparse bandwidth = 142055504 / (3.15962e+06 s / 16384) = 0.000686031 GB/s slice 21 write sparse bandwidth = 130388048 / (3.09774e+06 s / 16384) = 0.000642263 GB/s slice 20 write sparse bandwidth = 117964880 / (3.02676e+06 s / 16384) = 0.000594696 GB/s slice 19 write sparse bandwidth = 101560400 / (2.97198e+06 s / 16384) = 0.000521434 GB/s slice 18 write sparse bandwidth = 86372432 / (2.96247e+06 s / 16384) = 0.000444878 GB/s slice 18 write sections bandwidth = 1954957518434 / (1.83937e+07 s / 16384) = 1.62177 GB/s slice 17 write sparse bandwidth = 70170704 / (2.88973e+06 s / 16384) = 0.000370526 GB/s slice 17 write sections bandwidth = 1475380615039 / (1.36018e+07 s / 16384) = 1.65511 GB/s slice 17 read bandwidth (192 nodes) = 1475380615039 / 3383.36 s = 0.406122 GB/s per node: measured = 2.16598 MB/s, theoretical peak = 33.1341 MB/s Focusing on the "sparse" lines, the main point is that the time seems to be roughly independent of file size (plot attached). Each timing sample consists of (1) setup which I believe is negligible, (2) MPI_File_open, (3) MPI_File_write_ordered, (4) MPI_File_close. What might have caused these file writes to take so long? Geoffrey
