can you try again with at least 3 elements in other direction. On 13 Jan 2018, at 19:42, "[email protected] <mailto:[email protected]> " <[email protected] <mailto:[email protected]> > wrote: Thanks for the quick response. I made some global refinements but it seems I'm still getting the same error with genmap. Attached is the new .rea file with 4 elements in the periodic direction. On Sat, Jan 13, 2018 at 12:32 PM, <[email protected] <mailto:[email protected]> > wrote: You need to have at least three elements in the periodic direction. On 13 Jan 2018, at 19:19, "[email protected] <mailto:[email protected]> " <[email protected] <mailto:[email protected]> > wrote: Dear Nek Users, I am trying to get periodicity to work in the lastest version of Nek. I've made an extremely simple mesh within prenek (prex) in polar coordinates and cannot seem to run this case. When I run genmap, I get the error below. Did I do something wrong in setting up this mesh?
genmap reading a.rea Input mesh tolerance (default 0.2): NOTE: smaller is better, but generous is more forgiving for bad meshes. 0.01 reading mesh data ... start locglob_lexico: 4 2 8 1.0000000000000000E-002 locglob: 1 1 8 locglob: 2 5 8 locglob: 1 6 8 locglob: 2 6 8 done locglob_lexico: 6 6 8 2 start periodic vtx: 2 6 1 4 4 Matrix: x0 1 x0 1.0000E+00 1.0000E+00 5.4347-323 4.9407-324 2 x0 -3.5355E-01 3.5355E-01 6.9423-310 6.9423-310 3 x0 3.5355E-01 -3.5355E-01 6.9529-310 6.9529-310 4 x0 6.9423-310 6.9529-310 2.3477-313 3.1632-317 2 4 4 Matrix: x1 1 x1 1.0000E+00 1.0000E+00 6.3240-322 0.0000E+00 2 x1 -3.5355E-01 3.5355E-01 0.0000E+00 6.9423-310 3 x1 -3.5355E-01 3.5355E-01 6.9423-310 6.9529-310 4 x1 6.9423-310 6.9423-310 6.9423-310 6.9529-310 1 4 4 Matrix: z0 1 z0 1.0000E+00 1.0000E+00 5.4347-323 4.9407-324 2 z0 -2.1213E+00 -1.4142E+00 6.9423-310 6.9423-310 3 z0 2.1213E+00 1.4142E+00 6.9529-310 6.9529-310 4 z0 6.9423-310 6.9529-310 2.3477-313 3.1632-317 2 4 4 Matrix: z1 1 z1 1.0000E+00 1.0000E+00 6.3240-322 0.0000E+00 2 z1 1.4142E+00 2.1213E+00 0.0000E+00 6.9423-310 3 z1 1.4142E+00 2.1213E+00 6.9423-310 6.9529-310 4 z1 6.9423-310 6.9423-310 6.9423-310 6.9529-310 1 3 0 1.00000000E-03 2.12132000E+00 abort: FACE MATCH FAIL 2 4 3 2.12132000E-03 1.00000031E+00 abort: FACE MATCH FAIL
0 quit The mesh within my .rea file is as follows: 20.0000 20.0000 -8.00000 -4.00000 XFAC,YFAC,XZERO,YZERO **MESH DATA** 1st line is X of corner 1,2,3,4. 2nd line is Y. 2 2 2 NEL,NDIM,NELV ELEMENT 1 [ 1A] GROUP 0 -2.121320 -1.414213 -0.8742276E-07 -0.1311341E-06 2.121320 1.414213 2.000000 3.000000 ELEMENT 2 [ 1B] GROUP 0 -0.1311341E-06 -0.8742276E-07 1.414213 2.121320 3.000000 2.000000 1.414213 2.121320 ***** CURVED SIDE DATA ***** 4 Curved sides follow IEDGE,IEL,CURVE(I),I=1,5, CCURVE 2 1 -2.00000 0.00000 0.00000 0.00000 0.00000 C 4 1 3.00000 0.00000 0.00000 0.00000 0.00000 C 2 2 -2.00000 0.00000 0.00000 0.00000 0.00000 C 4 2 3.00000 0.00000 0.00000 0.00000 0.00000 C ***** BOUNDARY CONDITIONS ***** ***** FLUID BOUNDARY CONDITIONS ***** P 1 1 2.00000 3.00000 0.00000 0.00000 0.00000 W 1 2 0.00000 0.00000 0.00000 0.00000 0.00000 E 1 3 2.00000 1.00000 0.00000 0.00000 0.00000 W 1 4 0.00000 0.00000 0.00000 0.00000 0.00000 E 2 1 1.00000 3.00000 0.00000 0.00000 0.00000 W 2 2 0.00000 0.00000 0.00000 0.00000 0.00000 P 2 3 1.00000 1.00000 0.00000 0.00000 0.00000 W 2 4 0.00000 0.00000 0.00000 0.00000 0.00000 ***** NO THERMAL BOUNDARY CONDITIONS ***** <mime-attachment.png> _______________________________________________ Nek5000-users mailing list [email protected] <mailto:[email protected]> https://lists.mcs.anl.gov/mailman/listinfo/nek5000-users _______________________________________________ Nek5000-users mailing list [email protected] <mailto:[email protected]> https://lists.mcs.anl.gov/mailman/listinfo/nek5000-users _______________________________________________ Nek5000-users mailing list [email protected] <mailto:[email protected]> https://lists.mcs.anl.gov/mailman/listinfo/nek5000-users <a.rea>